Why does my MacBook say "Power Source: AC" but the battery is not charging?
That menu bar message simply means the Mac recognises that a charger is connected. It does not confirm that the charger is actually delivering usable power, or that the battery is accepting it. Those are separate stages in a chain: adapter, cable, port, power management chip, battery, and finally the logic board's charging controller.
In our Hyde Park workshop we see this fault presented in a few different ways. Some clients report the battery percentage frozen at, say, 43 percent for hours. Others see the lightning bolt icon flicker on and off. A third group finds that the Mac runs fine on the charger but dies the moment it is unplugged, which points strongly to the battery or the circuit that talks to it.
Is it the charger, the cable or the port?
Start here, because it costs nothing and rules out the simplest causes.
Try a different adapter and cable if you can borrow one, ideally a genuine Apple unit of the right wattage. Third-party chargers are a common culprit: a cheap USB-C charger may power the Mac just enough to run it but not enough to charge, particularly on a MacBook Pro that needs 61W or more. Check the cable along its length and at both connectors for kinks, fraying or discolouration. Inspect the adapter itself for scorch marks or a burning smell.
Then look at the port. On USB-C models, pocket lint, Highveld dust and the fine grit that settles on everything in Johannesburg collect inside the port and stop the connector seating fully. Shine a torch inside. If you see compacted debris, switch the Mac off and clean it gently with a wooden or plastic toothpick, never metal, and never compressed air held close. On older MacBooks with MagSafe, check the pins on the connector for dirt or burn marks, which usually mean the adapter is on its way out.
We also see a lot of damage from load shedding and power surges when power returns. A surge can kill an adapter outright, and sometimes it travels further and damages the charging circuitry on the board. If your problem started after a power cut or a storm, mention that when you contact us, because it changes where we look first.
What can I safely try at home before I book a repair?
There are a handful of steps worth doing, all of them safe for a non-technician:
What we strongly advise against is opening the Mac yourself to swap a battery with an unknown part, or prising at a swollen battery. If the trackpad is lifting, the case is bulging, or the lid no longer sits flat, stop using the Mac and stop charging it. A swollen lithium-ion cell is a genuine fire risk, and that is a job for a workshop.
When is the battery itself the problem?
Batteries are consumables. Each one has a finite number of charge cycles, and a heavily used MacBook that has been left plugged in for years in warm conditions will degrade faster. When a cell fails, the Mac may stop charging entirely, refuse to charge past a certain percentage, or shut down without warning at 30 or 40 percent.
A failed battery is the most common cause we find, and it is usually a straightforward fix. Our battery replacement service covers it, and it is worth doing properly: a quality cell, correctly fitted, with the adhesive and cable routing handled carefully, because rushed battery work is how trackpads and flex cables get damaged. If your Mac is more than four or five years old and charges unreliably, replacing the battery is often all it needs.
But here is the part many people miss: sometimes a new battery does not fix it. If we fit a good cell and the Mac still will not charge, the battery was never the real problem.
What is a board-level charging fault and how do you repair it?
When the adapter, cable, port and battery all test fine, the fault sits on the logic board. This is the territory where we spend most of our time, and where an independent specialist differs most from a swap-the-part approach.
The charging path on a MacBook board runs through several components: the USB-C controller chip (on many models a Texas Instruments unit), the charging controller, MOSFETs that switch power flow, small protection diodes, and a network of fuses and capacitors. We diagnose it with a bench power supply and a multimeter, measuring voltage at each stage to find where power stops. A shorted capacitor or a failed controller leaves a clear signature: the Mac may draw no current at all, or pull the wrong voltage.
Liquid exposure is a frequent cause here too. Even a small spill or humid-air corrosion can bridge tracks around the charging circuit, and our liquid damage process involves ultrasonic cleaning and microscope inspection before any component work begins. For genuine faults we carry out logic board repair by replacing the failed component under the microscope, rather than the whole board.
Is board-level repair better than replacing the Mac?
In most cases, yes, and it is not close. A dead charging circuit is usually one or two failed components on an otherwise healthy board. Replacing a few small parts costs a fraction of the cost of a new Mac, and it keeps your existing machine, your configuration and your data intact.
Replacement only makes sense when the board is damaged beyond economic repair, for instance after severe liquid damage that has corroded multiple layers, or on a very old model where the remaining life does not justify the work. We will tell you honestly when that is the case. We have repaired over 12,000 MacBooks since 2009, and a large share of the "dead" ones that arrive in a client's bag were one failed chip away from working again.
If your drive holds work you cannot lose, tell us up front. We can often recover it through our data recovery service before any other work begins.
How do I get my MacBook diagnosed in Johannesburg?
We offer a diagnostic assessment from R899 excluding VAT for Mac computers, which tells you exactly what has failed and what the repair involves before you commit to anything. You can see the full range of what we handle on our MacBook repair page.
To get started, WhatsApp us on 064 529 5863 with your model and a short description of the fault, or book online at zasupport.com/book. You can also reach us through our contact page.
Frequently Asked Questions
Why does my MacBook charge only when the screen is closed or the Mac is off?
This usually means the Mac is drawing more power than the charger supplies while it is running, so the battery gains nothing. It can point to an underpowered adapter, a faulty cable, or a battery that can no longer hold charge. Try a genuine Apple adapter of the correct wattage first.
Can a swollen MacBook battery stop it from charging?
Yes, and it is a safety concern as well. Swelling means the cell is failing internally, and the Mac may stop charging to protect itself. If your trackpad is lifting or the case is bulging, stop using the Mac and have the battery replaced by a workshop promptly.
Will resetting the SMC fix a MacBook that is not charging?
Only on Intel MacBooks, and only when the fault is a software-level power management confusion. Apple silicon Macs have no separate SMC reset, as that function is built into the chip. If a reset does not help, the problem is hardware.
Can I keep using my MacBook while it will not charge?
You can run it plugged in, but it is not ideal. The Mac may shut down suddenly if the supply is unstable, which risks unsaved work and, over time, file system corruption. Back up what matters and arrange a diagnosis.
Does a third-party charger cause charging problems?
It can. Cheap chargers often fail to deliver the stable voltage and negotiated wattage a MacBook expects, and some can damage the charging circuitry over time. Always use a genuine Apple adapter or a reputable one rated for your model.
How long does a MacBook charging repair take?
A simple battery replacement is often completed the same day or the next. Board-level work takes longer because it involves careful diagnosis and microscope soldering, and the timeline depends on the fault found. We confirm an estimate after the diagnostic assessment so you know what to expect.
